Ridge tape

Product description

Bramps for non -combinted photovoltaics

Ridge tape is used to seal ridge tiles of ventilated sloping roof coverings lying on battens and counter battens. It is fixed on the ridges and corners, under the ridge tiles, on already laid coverings. The tape provides good ventilation conditions for the slope and protects against the penetration of water (snow, rain), as well as dust and dust under the cover.

The ridge tape is used in the case of coverings made of tiles, especially for cement espressoes and ceramic uninterested tiles, which do not require high breathable tape. It consists of 2 aluminum belts between which there is polypropylene fabric. Specially profiled edges of the tape enable installation on every type of roofing, and are used to efficiently drain water from precipitation. The butyl coating placed on the edges, allows you to permanently connect the tape with the roofing. The tape sticks on porous and smooth surfaces, but it should be remembered that the glued surface should be free of fat and dust.

Inspirations

Single -family House Tuczępa

A single -family house in Rytwiny

Single -family house, Staszów

Villa in Niepołomice

Arkadia Investment housing estate

Single -family house, Pliskowola

Sevilla Gold Hotel

Arena Grupa Azoty in Puławy

Kielce bus station

Avant -garde design in a public building

Końskie - gable

A single -family house in Rudna near Rzeszów

Flat metal sheet, single -family house in Rudna

Flat metal tile market, Orzysz

Trapeze

Tur

Modus

Detached house complex roof. Modus roof tile

Modus metal roof tile, multi -track roof

Mercedes

Leroy Merlin

Technical specification

General information

Material

aluminum + butyl glue + PP fabric

roll size

240 mm x 5 mb

packaging

4 roll/carton

Available colours

brown,
brick red,
black,
cherry

Download

Do you have questions?

Is it possible to make copper machining at the steel roof?

When using copper, be careful because copper oxides are very aggressive and cause corrosion of other metals. Therefore, on buildings, it cannot be combined with other metal species (copper enters into contact and causes electrolytic corrosion of other metals).

Why is the metal roofing sheets recommended for the renovation of old roofs?

This is directly related to its low weight. In the case of old roofs, the trusses of the renovated houses are often somewhat damaged by time. Therefore, it is safer to use a metal roofing tile, which weight oscillates at 4.7 kg/m2, than almost ten times a heavier ceramic tile than it. However, it is always worth verifying the condition of the roof truss, with a specialist and make sure that it does not require renovation or replacement. In such cases, the safety of residents or building employees, as well as the assembly team, is always a priority. In most situations, however, the condition of the structure without major problems allows the use of roof tiles, while the use of ceramic tile would not be possible.

Can you use an angle grinder when cutting sheets?

Modern roofing exclude the use of angle grinders for cutting. The use of this method of cutting the material is associated with the loss of warranty.The angle grinder during operation and cutting produces very large amounts of heat, which in turn damages the edges of the sheet, as well as the coating covering it. In addition, the filings extracting during operation blend into the surface of the blades, additionally creating potential corrosion outbreaks.The right way of cutting sheet metal is to use automatic jumps (so -called Nilerler) or hand scissors. They use the mechanical force to cut the sheet, without exposing it to high temperature jumps. In addition, it is worth remembering that after cutting it is good to train cut places with dedicated protective varnish or special paint.

Does the roof require maintenance?

Yes, each roof requires periodic inspections to check if there have been any damage. Most of the products offered by Blachy Pruszyński have various types of specialized coatings available (covered by the warranty), increasing the life and durability of sheet metal. Maintenance consists mainly in removing the deposits and chimney dust, which left for a longer period of time can lead to sheet metal damage. Particular attention should be paid to places around chimneys that are sensitive due to more demanding operating conditions. If during the coverage inspection, local damage to the paint coating will be noticed, paint corrections should be made. In such a situation, the best solution is to use dedicated gloss paints tailored to a given coating. Such paints are in a stringent offer of Pruszyńska sheet and it is strongly recommended to use company products, recommended for a given coating.

How to register and how does the warranty work?

In order to register the warranty, download the warranty registration available in files for download / printing or directly: Warranty registration and send it completed to the following address: guarantee@pruszynski.euThe warranty begins to apply on the day of purchase of the goods. Registration of warranty is necessary to quickly identify the purchased batch of goods.

How can you complain the product, where is the information?

Complaints should be submitted in a warehouse in which the purchase was made. In the event that the wholesaler has been closed (does not run a business), the filled print of the complaint application should be sent directly to Pruszyński Sp. z o.o. to: pruszynski@pruszynski.eu

Printing of the complaint application is available in files for download / prints or directly here: Complaints

Worth seeing

Trapezoidal sheets

See the offer

Others in this category

Wkręty samowiercące typu OC do łączenia blach i konstrukcji do 12 mm

Roofing fasteners - 12mm

Bet metal fasteners