Karta produktu Loara – modular roof tile – panel
Home / Produkty / Roofs / Panel/modular roof tile / Loara – modular roof tile – panel Loara - modular roof tile - panel Where to buy? Pobierz kartę produktu Technical Specifications Order online Description Download ISOD System Technical specification General information length of module: 350 mm height of bending: 30 mm height of profile: 23 mm effective width: 1120 mm total width: ~1187 mm min. slope of roof: 15° Recommendations Transport and storage It is of course the best to unload in original manufacturer packaging, using mechanical unloading equipment. Unloading shall be carried out by the proper number of people, that is in the case of long sheets (ca. 6 linear metre) the sheets shall be unloaded by 6 people, three on each side. Special attention shall be paid not to friction one sheet against one another, bend the side edges or stretch the sheet. Steel sheet deformation during the unloading and moving can result in problems with proper installation (chinks in clamps). Galvanised and aluzinc steel sheets must be protected against getting wet! If the customer collects the product with his own means of transportation, the vehicle shall have an open loading platform allowing for easy loading and unloading, with the length suitable for ordered sheets. The sheets shall not extend beyond the platform. Proper anchoring of the sheet packages for the transport will reduce the damage of the sheet paint coat due to abrasion. Maintenance and washing In order to extend durability of roofs and elevations it’s recommended to check and conserve it. Inspection – One time a year (best in spring) there should be inspection of roof/elevation for early detection of possible damage. Cleaning of steel sheet – Roof and elevation made of steel sheets require cleaning at least once a year. Stratifying dirt on steel sheet may cause uneven discoloration of lacquer (because of uneven impact of UV beams), and lower protection to corrosion(dust traps humidity on steel sheets which causes damage). Dirty and stained spots can be cleaned by soft brush and water (temp. max. 60c). If it is necessary it is permitted to use some light detergent (ph 6/7, max 10% solution). There also can be used pressed water(max. 100bar) to cleaning, however the beam of water cannot be applicated too near of surface of sheets(min. 30 cm), also it shouldn’t be perpendicularly to surface. Near the connections water beam should be directed to bottom, to avoid water of entering cracks near connections. With old surfaces of steel sheets we should deal with high cautiously. Cleaning should be conducted from top to bottom, and cleaned spots should be rinsed out immediately. It is not permitted to use scouring powders, nitro solvent, chlorine liquor, aromatised substances, substances with amon chloride or sodium. Damages – Possible damages during guarantee should be consulted with Contractor of roof/elevation and can be repaired only with his written permission.Repair of damages on small surfaces is done with quick-drying varnish. However painting big surfaces should be done with special industrial paints dedicated to renovating coverings. Painting should be limited only to special damaged spots (scratches to steel, centres of corrosion etc.)Preparation of surface to painting should be done with generally accepted rules. It is necessary to precisely remove all signs of corrosion – best with special brush or close-grained sandpaper. Then that surface should be undusted, degreased and cleaned. To degrease extraction naptha or water with addition of surfactant(best with 1-2%solution of ammoniac) can be used. Repaired spots may be different in colour compared to original steel sheets because of natural impact of atmospheric phenomenon (ageing of varnish due to impact of UV radiation) ATTENTION!– During inspecting, cleaning, conservation and repair all work safety regulations should be obeyed.Pruszyński Sp. z o.o. is not in charge of possible accidents during carrying out all following actions. Choose a coating: Protective coatings PURMATpolyurethane, matt Technical specification of the coating Thickness of coating 50 µm Corrosion resistance High ★★★★ UV resistance High ★★★★ Possibility of bending High ★★★☆ Aestetic warranty 30 years Technical warranty 50 years Available colours PUM R011 PUM R028 PUM R033 PUM R750 PUM RAL 7016 PUM RAL 8017 PURLAKpolyurethane, glossy Technical specification of the coating Thickness of coating 50 µm Corrosion resistance High ★★★★ UV resistance High ★★★☆ Possibility of bending High ★★★☆ Aestetic warranty 30 years Technical warranty 50 years Available colours PU RAL 7016 PU RAL 9005 TOPMAT®poliyester, matt (Arcelor DE) Technical specification of the coating Thickness of coating 35 µm Corrosion resistance High ★★★★ UV resistance High ★★★★ Possibility of bending High ★★★☆ Aestetic warranty 20 years Technical warranty 35 years Available colours TOPMAT R033 TOPMAT R750 TOPMAT RAL 7016 TOPMAT RAL 8017 ULTRAMAT®poliyester, matt (Arcelor PL) Technical specification of the coating Thickness of coating 35 µm Corrosion resistance High ★★★★ UV resistance High ★★★★ Possibility of bending High ★★★☆ Aestetic warranty 15 years Technical warranty 35 years Available colours 0,5 mm PMG R011 PMG R028 PMG R032 PS25poliyester, glossy Technical specification of the coating Thickness of coating 25 µm Corrosion resistance High ★★★☆ UV resistance Good ★★☆☆ Possibility of bending Good ★★☆☆ Aestetic warranty 10 years Technical warranty 30 years Available colours 0,5 mm R028 R032 RAL 1002 RAL 1015 RAL 1021 RAL 3000 RAL 3005 RAL 3016 RAL 5010 RAL 6005 RAL 6029 RAL 7000 RAL 7016 RAL 7024 RAL 7035 RAL 8004 RAL 8017 RAL 9002 RAL 9005 RAL 9006 SILVER RAL 9007 SILVER METALLIC RAL 9010 The PRUSZYŃSKI company guarantees the execution of each order in the same color (shade). However, due to the complexity of the coating processes, there may be differences in shades between individual deliveries. Responsibility for the color is therefore limited to one delivery only. In connection with the above, in the case of ordering sheets for a specific batch, please indicate on the order or inform the Trader that it is a continuation of the order and the delivery of a color sample. In order to ensure color consistency of sandwich panels with other elements, such as flashings, they should be ordered from one supplier. Product description Roofing tile with character Loara’s roof tile was created by refining the shape of the Tur panel cover. Higher embossing is an interesting continuation of the series, which is popular among customers. The roof tile is symmetrical, which greatly facilitates the assembly process. Tags Loara Modular metal roofing tile metal roofing tile See our offer of accessories Choose the best accessories for your roof! Roof membranes See product Omega Ridge (large) Ridges See product Seals Roof accessories See product TORX self-drilling screws (staples) Fasteners for trapezoidal sheets, roof tiles, karo panels (short) See product Ventilation eaves batten Roof flashings See product
Pruszyński Sp. z o.o Sokołów, 05-806 Komorów ul. Sokołowska 32b Tel. (48-22) 738 60 00 Fax (48-22) 738 61 01 Infolinia: 880 222 444 pruszynski.com.pl pruszynski@pruszynski.com.pl

Loara - Blachodachówka modułowa - panelowa

Loara - modular roof tile - panel

Where to buy? Pobierz kartę produktu

Technical specification

General information

length of module:

350 mm

height of bending:

30 mm

height of profile:

23 mm

effective width:

1120 mm

total width:

~1187 mm

min. slope of roof:

15°

Loara - Blachodachówka modułowa - panelowa - przekroj

Recommendations

Transport and storage

It is of course the best to unload in original manufacturer packaging, using mechanical unloading equipment.
Unloading shall be carried out by the proper number of people, that is in the case of long sheets (ca. 6 linear metre) the sheets shall be unloaded by 6 people, three on each side. Special attention shall be paid not to friction one sheet against one another, bend the side edges or stretch the sheet. Steel sheet deformation during the unloading and moving can result in problems with proper installation (chinks in clamps).
Galvanised and aluzinc steel sheets must be protected against getting wet!
If the customer collects the product with his own means of transportation, the vehicle shall have an open loading platform allowing for easy loading and unloading, with the length suitable for ordered sheets. The sheets shall not extend beyond the platform. Proper anchoring of the sheet packages for the transport will reduce the damage of the sheet paint coat due to abrasion.

Maintenance and washing

In order to extend durability of roofs and elevations it’s recommended to check and conserve it.
Inspection – One time a year (best in spring) there should be inspection of roof/elevation for early detection of possible damage.
Cleaning of steel sheet – Roof and elevation made of steel sheets require cleaning at least once a year. Stratifying dirt on steel sheet may cause uneven discoloration of lacquer (because of uneven impact of UV beams), and lower protection to corrosion(dust traps humidity on steel sheets which causes damage). Dirty and stained spots can be cleaned by soft brush and water (temp. max. 60c). If it is necessary it is permitted to use some light detergent (ph 6/7, max 10% solution). There also can be used pressed water(max. 100bar) to cleaning, however the beam of water cannot be applicated too near of surface of sheets(min. 30 cm), also it shouldn’t be perpendicularly to surface. Near the connections water beam should be directed to bottom, to avoid water of entering cracks near connections. With old surfaces of steel sheets we should deal with high cautiously. Cleaning should be conducted from top to bottom, and cleaned spots should be rinsed out immediately.
It is not permitted to use scouring powders, nitro solvent, chlorine liquor, aromatised substances, substances with amon chloride or sodium.
Damages – Possible damages during guarantee should be consulted with Contractor of roof/elevation and can be repaired only with his written permission.Repair of damages on small surfaces is done with quick-drying varnish. However painting big surfaces should be done with special industrial paints dedicated to renovating coverings. Painting should be limited only to special damaged spots (scratches to steel, centres of corrosion etc.)Preparation of surface to painting should be done with generally accepted rules. It is necessary to precisely remove all signs of corrosion – best with special brush or close-grained sandpaper. Then that surface should be undusted, degreased and cleaned. To degrease extraction naptha or water with addition of surfactant(best with 1-2%solution of ammoniac) can be used. Repaired spots may be different in colour compared to original steel sheets because of natural impact of atmospheric phenomenon (ageing of varnish due to impact of UV radiation)
ATTENTION!– During inspecting, cleaning, conservation and repair all work safety regulations should be obeyed.Pruszyński Sp. z o.o. is not in charge of possible accidents during carrying out all following actions.

PURMATpolyurethane, matt

Technical specification of the coating

Thickness of coating

50 µm

Corrosion resistance

High ★★★★

UV resistance

High ★★★★

Possibility of bending

High ★★★☆

Aestetic warranty

30 years

Technical warranty

50 years

Available colours

PUM R011

PUM R028

PUM R033

PUM R750

PUM RAL 7016

PUM RAL 8017

PURLAKpolyurethane, glossy

Technical specification of the coating

Thickness of coating

50 µm

Corrosion resistance

High ★★★★

UV resistance

High ★★★☆

Possibility of bending

High ★★★☆

Aestetic warranty

30 years

Technical warranty

50 years

Available colours

PU RAL 7016

PU RAL 9005

TOPMAT®poliyester, matt (Arcelor DE)

Technical specification of the coating

Thickness of coating

35 µm

Corrosion resistance

High ★★★★

UV resistance

High ★★★★

Possibility of bending

High ★★★☆

Aestetic warranty

20 years

Technical warranty

35 years

Available colours

TOPMAT R033

TOPMAT R750

TOPMAT RAL 7016

TOPMAT RAL 8017

ULTRAMAT®poliyester, matt (Arcelor PL)

Technical specification of the coating

Thickness of coating

35 µm

Corrosion resistance

High ★★★★

UV resistance

High ★★★★

Possibility of bending

High ★★★☆

Aestetic warranty

15 years

Technical warranty

35 years

Available colours

0,5 mm

PMG R011

PMG R028

PMG R032

PS25poliyester, glossy

Technical specification of the coating

Thickness of coating

25 µm

Corrosion resistance

High ★★★☆

UV resistance

Good ★★☆☆

Possibility of bending

Good ★★☆☆

Aestetic warranty

10 years

Technical warranty

30 years

Available colours

0,5 mm

R028

R032

RAL 1002

RAL 1015

RAL 1021

RAL 3000

RAL 3005

RAL 3016

RAL 5010

RAL 6005

RAL 6029

RAL 7000

RAL 7016

RAL 7024

RAL 7035

RAL 8004

RAL 8017

RAL 9002

RAL 9005

RAL 9006<br><span style="font-size: 7pt;">SILVER</span>

RAL 9006
SILVER

RAL 9007<br><span style="font-size: 7pt;">SILVER METALLIC</span>

RAL 9007
SILVER METALLIC

RAL 9010

The PRUSZYŃSKI company guarantees the execution of each order in the same color (shade). However, due to the complexity of the coating processes, there may be differences in shades between individual deliveries.

Responsibility for the color is therefore limited to one delivery only.

In connection with the above, in the case of ordering sheets for a specific batch, please indicate on the order or inform the Trader that it is a continuation of the order and the delivery of a color sample.

In order to ensure color consistency of sandwich panels with other elements, such as flashings, they should be ordered from one supplier.

Product description

Roofing tile with character

Loara’s roof tile was created by refining the shape of the Tur panel cover.

Higher embossing is an interesting continuation of the series, which is popular among customers. The roof tile is symmetrical, which greatly facilitates the assembly process.