Karta produktu
MODUS – Modular roof tile – panel
MODUS - Modular roof tile - panel
Technical specification
General information
length of module:
350 mm
length of module:
25 mm
height of profile:
34 mm
effective width:
1080 mm
total width:
~1179 mm
min. slope of roof:
15°
Recommendations
Transport and storage
- It is of course the best to unload in original manufacturer packaging, using mechanical unloading equipment.
- Unloading shall be carried out by the proper number of people, that is in the case of long sheets (ca. 6 linear metre) the sheets shall be unloaded by 6 people, three on each side. Special attention shall be paid not to friction one sheet against one another, bend the side edges or stretch the sheet. Steel sheet deformation during the unloading and moving can result in problems with proper installation (chinks in clamps).
- Galvanised and aluzinc steel sheets must be protected against getting wet!
- If the customer collects the product with his own means of transportation, the vehicle shall have an open loading platform allowing for easy loading and unloading, with the length suitable for ordered sheets. The sheets shall not extend beyond the platform. Proper anchoring of the sheet packages for the transport will reduce the damage of the sheet paint coat due to abrasion.
- It is of course the best to unload in original manufacturer packaging, using mechanical unloading equipment.
- Unloading shall be carried out by the proper number of people, that is in the case of long sheets (ca. 6 linear metre) the sheets shall be unloaded by 6 people, three on each side. Special attention shall be paid not to friction one sheet against one another, bend the side edges or stretch the sheet. Steel sheet deformation during the unloading and moving can result in problems with proper installation (chinks in clamps).
- Galvanised and aluzinc steel sheets must be protected against getting wet!
- If the customer collects the product with his own means of transportation, the vehicle shall have an open loading platform allowing for easy loading and unloading, with the length suitable for ordered sheets. The sheets shall not extend beyond the platform. Proper anchoring of the sheet packages for the transport will reduce the damage of the sheet paint coat due to abrasion.
Maintenance and washing
- In order to extend durability of roofs and elevations it’s recommended to check and conserve it.
- Inspection – One time a year (best in spring) there should be inspection of roof/elevation for early detection of possible damage.
- Cleaning of steel sheet – Roof and elevation made of steel sheets require cleaning at least once a year. Stratifying dirt on steel sheet may cause uneven discoloration of lacquer (because of uneven impact of UV beams), and lower protection to corrosion(dust traps humidity on steel sheets which causes damage). Dirty and stained spots can be cleaned by soft brush and water (temp. max. 60c). If it is necessary it is permitted to use some light detergent (ph 6/7, max 10% solution). There also can be used pressed water(max. 100bar) to cleaning, however the beam of water cannot be applicated too near of surface of sheets(min. 30 cm), also it shouldn’t be perpendicularly to surface. Near the connections water beam should be directed to bottom, to avoid water of entering cracks near connections. With old surfaces of steel sheets we should deal with high cautiously. Cleaning should be conducted from top to bottom, and cleaned spots should be rinsed out immediately.
- It is not permitted to use scouring powders, nitro solvent, chlorine liquor, aromatised substances, substances with amon chloride or sodium.
- Damages – Possible damages during guarantee should be consulted with Contractor of roof/elevation and can be repaired only with his written permission.Repair of damages on small surfaces is done with quick-drying varnish. However painting big surfaces should be done with special industrial paints dedicated to renovating coverings. Painting should be limited only to special damaged spots (scratches to steel, centres of corrosion etc.)Preparation of surface to painting should be done with generally accepted rules. It is necessary to precisely remove all signs of corrosion – best with special brush or close-grained sandpaper. Then that surface should be undusted, degreased and cleaned. To degrease extraction naptha or water with addition of surfactant(best with 1-2%solution of ammoniac) can be used. Repaired spots may be different in colour compared to original steel sheets because of natural impact of atmospheric phenomenon (ageing of varnish due to impact of UV radiation)
- ATTENTION!– During inspecting, cleaning, conservation and repair all work safety regulations should be obeyed.Pruszyński Sp. z o.o. is not in charge of possible accidents during carrying out all following actions.
- In order to extend durability of roofs and elevations it’s recommended to check and conserve it.
- Inspection – One time a year (best in spring) there should be inspection of roof/elevation for early detection of possible damage.
- Cleaning of steel sheet – Roof and elevation made of steel sheets require cleaning at least once a year. Stratifying dirt on steel sheet may cause uneven discoloration of lacquer (because of uneven impact of UV beams), and lower protection to corrosion(dust traps humidity on steel sheets which causes damage). Dirty and stained spots can be cleaned by soft brush and water (temp. max. 60c). If it is necessary it is permitted to use some light detergent (ph 6/7, max 10% solution). There also can be used pressed water(max. 100bar) to cleaning, however the beam of water cannot be applicated too near of surface of sheets(min. 30 cm), also it shouldn’t be perpendicularly to surface. Near the connections water beam should be directed to bottom, to avoid water of entering cracks near connections. With old surfaces of steel sheets we should deal with high cautiously. Cleaning should be conducted from top to bottom, and cleaned spots should be rinsed out immediately.
- It is not permitted to use scouring powders, nitro solvent, chlorine liquor, aromatised substances, substances with amon chloride or sodium.
- Damages – Possible damages during guarantee should be consulted with Contractor of roof/elevation and can be repaired only with his written permission.Repair of damages on small surfaces is done with quick-drying varnish. However painting big surfaces should be done with special industrial paints dedicated to renovating coverings. Painting should be limited only to special damaged spots (scratches to steel, centres of corrosion etc.)Preparation of surface to painting should be done with generally accepted rules. It is necessary to precisely remove all signs of corrosion – best with special brush or close-grained sandpaper. Then that surface should be undusted, degreased and cleaned. To degrease extraction naptha or water with addition of surfactant(best with 1-2%solution of ammoniac) can be used. Repaired spots may be different in colour compared to original steel sheets because of natural impact of atmospheric phenomenon (ageing of varnish due to impact of UV radiation)
- ATTENTION!– During inspecting, cleaning, conservation and repair all work safety regulations should be obeyed.Pruszyński Sp. z o.o. is not in charge of possible accidents during carrying out all following actions.
Polyester glossy
Technical specification of the coating
thickness of a coating
25 µm
Corrosion resistance
High ★★★☆
UV resistance
Good ★★☆☆
Possibility of processing
Good ★★☆☆
Aesthetic warranty
10 years
Technical warranty
30 years
Available colours
Polyester matt structural
Technical specification of the coating
thickness of a coating
35 µm
corrosion resistance
High ★★★☆
UV resistance
Good ★★☆☆
Possibility of processing
Good ★★☆☆
Aesthetic warranty
15 years
technical warranty
35 years
Available colours
PMG RR 011
PMG RR 028
PMG RR 032
TOPMAT
Technical specification of the coating
thickness of a coating
35 µm
corrosion resistance
High ★★★★
UV resistance
High ★★★★
Possibility of processing
High ★★★☆
Aesthetic warranty
20 years
technical warranty
35 years
Available colours
TOPMAT RR 750
TOPMAT RR 033
TOPMAT RAL 7016
TOPMAT RAL 8017
PURMAX
Technical specification of the coating
thickness of a coating
40 µm
corrosion resistance
High ★★★★
UV resistance
High ★★★★
Possibility of processing
High ★★★☆
Aesthetic warranty
20 years
technical warranty
40 years
Available colours
RAL 8004
PURLAK
Technical specification of the coating
thickness of a coating
50 µm
corrosion resistance
Wysoka ★★★★
UV resistance
High ★★★☆
Possibility of processing
High ★★★☆
Aesthetic warranty
up to 30 years
technical warranty
50 years
Available colours
PURMAT
Technical specification of the coating
thickness of a coating
50 µm
corrosion resistance
High ★★★★
UV resistance
High ★★★★
Possibility of processing
High ★★★☆
Aesthetic warranty
do 30 years
technical warranty
50 years
Available colours
PUM RR 750
PUM RR 011
PUM RR 028
PUM RR 033
PUM RAL 7016
PUM RAL 8017
Pruszyński Company guarantess realization of each order in one colour shade. Although due to technological process of covering paint to steel shets there is possibility for occuring difference in colour shade in different deliveries.
Regarding this please inform sales person if different delivery is continuation of previous orders.
Product description
Roofing tile with character
Panel Modus is a metal roof tile cut on the edge, it is available in the form of dual -dual panels.
They are perfect as roofing with a complex slope, guaranteeing and minimum amount of waste.
Tags
See our offer of accessories
Choose the best accessories for your roof!
Pruszyński Sp. z o.o
Sokołów, 05-806 Komorów
ul. Sokołowska 32b
Tel. (48-22) 738 60 00
Fax (48-22) 738 61 01
Infolinia: 880 222 444