Technical specification

General information

All Karo roof panels are only available in coatings - gloss or matte polyester (up to 30 or 35 years warranty) as well as purmat (up to 50 years warranty).

Panel size
555 x 555 mm
material
polyester mat PMG / PURMAT
steel thickness
0,5 mm
Method of assembly 
With fastener of hook and eye

on full planked roof
Method of assembly 
roofs of min. slope 22°
Accessories
fasteners, sealings tapes, flashings
Panel dachowy Karo 555 - przekroj

Recommendations

Transport and storage

  • Packages should be stored in dry and well-ventilated spaces, without humidity condensation  between the sheets. Collective packages should be put on blocks about 20cm height upon the surface. If panels are stored more than 3 weeks from the production date – panels should be checked and separators should be put between to allow for free air circulation. All information about the way and period of storage are on the protective foil, product labels and our catalogues, assembly instructions and website.
  • Protective foil is used to safe the roof panels against mechanical damages. It should be removed directly at the assembly stage and it should protect panels against humidity and sun during the storage period. Non compliance with above rules may cause difficulties when removing the foil from sheets and dirty after the glue

Maintenance and washing

  • In order to extend durability of roofs and elevations it’s recommended to check and conservative it.
  • Inspection – One time a year (it’s best in spring) there should be inspection of roof/elevation in order to early detection of possible damage.
  • Cleaning of steel sheet – Roof and elevation made of steel sheets require cleaning at least once a year. Stratifying dirt on steel sheet may cause uneven discoloration of lacquer (because of uneven impact of UV beams), and lower protection to corrosion(dust traps humidity on steel sheets which causes damage). Dirty and stained spots can be cleaned by soft brush and water (temp. max. 60c). If it is necessary it is permitted to use some light detergent (ph 6/7, max 10% solution). There also can be used pressed water(max. 100bar) to cleaning, however the beam of water cannot be applicated too near of surface of sheets(min. 30 cm), also it shouldn’t be perpendicularly to surface. Near the connections water beam should be directed to bottom, to avoid water of entering cracks near connections. With old surfaces of steel sheets we should deal with high cautiously. Cleaning should be conducted from top to bottom, and cleaned spots should be rinsed out immediately.
  •  It is not permitted to use scouring powders, nitro solvent, chlorine liquor, aromatised substances, substances with Amon chloride or sodium.
  • Damages – Possible damages during guarantee should be consulted with Contractor of roof/elevation and can be repaired only with his written permission.Repair of damages on small surfaces is done with quick-drying varnish. However painting big surfaces should be done with special industrial paints to renovating coverings. Painting should be limited only to special damaged spots (scratches to steel, centres of corrosion etc.)

    Preparation of surface to painting should be done with generally accepted rules. It is necessary to precisely remove all signs of corrosion – best with special brush or  close-grained sandpaper. Then that surface should be undusted, degreased and cleaned. To degrease extraction naptha or water with addition of surfactant(best with 1-2%solution of ammoniac) can be used. Repaired spots may be different in colour compared to original steel sheets because of natural impact of atmospheric phenomenon (ageing of varnish due to impact of UV radiation)

  • ATTENTION!– During inspecting, cleaning, conservation and repair all work safety regulations should be obeyed.Pruszyński Sp. z o.o. is not in charge of possible accidents during carrying out all following actions.
Choose a coating:
More information about the coatings
polyester glossy

Technical specification of the coating

thickness of coating
25 µm
corrosion resistance
High ★★★☆
UV resistance
Good ★★☆☆
possibility of bending
Good ★★☆☆
Aesthetic warranty
10 years
Technical warranty
30 years

Available colours

TOPMAT

Technical specification of the coating

thickness of coating
35 µm
corrosion resistance
High ★★★☆
UV resistance
Good ★★☆☆
possibility of bending
Good ★★☆☆
Aesthetic warranty
15 years
Technical warranty
35 years

Available colours

PMG RAL 7016
PMG RR 033
PMG RAL 8017
PMG RR 032
PMG RR 028
PMG RR 750
PMG RR 011
PURMAT

Technical specification of the coating

thickness of coating
50 µm
corrosion resistance
High ★★★★
UV resistance
High ★★★★
possibility of bending
High ★★★☆
Aesthetic warranty
up to 30 years
Technical warranty
50 years

Available colours

PUM RAL 7016
PUM RAL 7016
PUM RR 033
PUM RR 033
PUM RAL 8017
PUM RAL 8017
PUM RR 028
PUM RR 011
PUM RR 750
PUM RR 750
Firma PRUSZYŃSKI gwarantuje każdorazowo realizację poszczególnego zamówienia w jednakowym kolorze (odcieniu). Z uwagi na skomplikowanie procesów powlekania możliwe jest jednak występowanie różnic w odcieniach pomiędzy poszczególnymi dostawami.

Odpowiedzialność za kolor w związku z tym ograniczona jest jedynie do jednej dostawy.

W związku z powyższym w przypadku domawiania blach do konkretnej partii bardzo prosimy o zaznaczenie na zamówieniu lub poinformowanie Handlowca, iż jest to kontynuacja zlecenia oraz dostarczenia próbki kolorystycznej.

Celem zapewnienia spójności kolorystycznej płyty warstwowych z innymi elementami takimi jak np. obróbki blacharskie należy zamawiać je u jednego dostawcy.

Pruszyński Company guarantess realization of each order in one colour shade. Although due to technological process of covering paint to steel shets there is possibility for occuring difference in colour shade in different deliveries.

Regarding this please inform sales person if different delivery is continuation of previous orders.

Product description

Karo roof panels

Made of coated sheet, it is an excellent choice for all those who want their roof to look original. They are mounted on roofs with full formwork on the so -called embroidery. An interesting shape of this cover guarantees that the entire building will gain a unique character.

Made of coated sheet, it is an excellent choice for all those who want their roof to look original. They are mounted on roofs with full formwork on the so -called embroidery. An interesting shape of this cover guarantees that the entire building will gain a unique character.

See our offer of accessories

Choose the best accessories for your roof!

Wkręty samowiercące typu TORX TORX screws for connecting steel sheets
Connectors for metal roofing sheets, trapezoidal sheets, Karo panels (long)
See product
Haftra - Uchwyt mocujący do panelu Karo Embroidery
Fastening holder to the Karo panel
See product