PS panel
Technical specification
General information
Wall panels are available in two variants of utility wide. 155 /215 mm - made of sheet metal 0.5 to 0.7 mm and 315 mm - which is produced only 0.7 mm thick sheet We also sensitize our clients to the specifics of assembly and compliance with assembly recommendations in the case of this product. They are described in detail in the section: cutting and assembly
---
315 mm
---
0,7 mm
Recommendations
Transport and storage
- Transport of trapezoidal sheets should be done with special vehicle which shall have an open loading platform allowing easy loading and unloading, with the length suitable for ordered sheets. The sheets shall not extend beyond the platform otherwise it may cause damage and in consequence loss of the guarantee . The steel sheets must be protected against drifting and soaking.
- Unloading shall be carried out by the proper number of people, that is in the case of long sheets (ca. 6linear metre) the sheets shall be unloaded by 6 people, three on each side.
- Special attention shall be paid not to friction one sheet against the other, bend the side edges or stretch the sheet. Steel sheet deformation during the unloading and moving can result in problems with proper installation (chinks in clamps). It is of course the best to unload in original manufacturer packaging , using mechanical unloading equipment.
- Special carefulness should be maintained during unloading in winter and during storing in heated warehouses.
- Transport of trapezoidal sheets should be done with special vehicle which shall have an open loading platform allowing easy loading and unloading, with the length suitable for ordered sheets. The sheets shall not extend beyond the platform otherwise it may cause damage and in consequence loss of the guarantee . The steel sheets must be protected against drifting and soaking.
- Unloading shall be carried out by the proper number of people, that is in the case of long sheets (ca. 6linear metre) the sheets shall be unloaded by 6 people, three on each side.
- Special attention shall be paid not to friction one sheet against the other, bend the side edges or stretch the sheet. Steel sheet deformation during the unloading and moving can result in problems with proper installation (chinks in clamps). It is of course the best to unload in original manufacturer packaging , using mechanical unloading equipment.
- Special carefulness should be maintained during unloading in winter and during storing in heated warehouses.
- Transport of trapezoidal sheets should be done with special vehicle which shall have an open loading platform allowing easy loading and unloading, with the length suitable for ordered sheets. The sheets shall not extend beyond the platform otherwise it may cause damage and in consequence loss of the guarantee . The steel sheets must be protected against drifting and soaking.
- Unloading shall be carried out by the proper number of people, that is in the case of long sheets (ca. 6linear metre) the sheets shall be unloaded by 6 people, three on each side.
- Special attention shall be paid not to friction one sheet against the other, bend the side edges or stretch the sheet. Steel sheet deformation during the unloading and moving can result in problems with proper installation (chinks in clamps). It is of course the best to unload in original manufacturer packaging , using mechanical unloading equipment.
- Special carefulness should be maintained during unloading in winter and during storing in heated warehouses.
- Transport of trapezoidal sheets should be done with special vehicle which shall have an open loading platform allowing easy loading and unloading, with the length suitable for ordered sheets. The sheets shall not extend beyond the platform otherwise it may cause damage and in consequence loss of the guarantee . The steel sheets must be protected against drifting and soaking.
- Unloading shall be carried out by the proper number of people, that is in the case of long sheets (ca. 6linear metre) the sheets shall be unloaded by 6 people, three on each side.
- Special attention shall be paid not to friction one sheet against the other, bend the side edges or stretch the sheet. Steel sheet deformation during the unloading and moving can result in problems with proper installation (chinks in clamps). It is of course the best to unload in original manufacturer packaging , using mechanical unloading equipment.
- Special carefulness should be maintained during unloading in winter and during storing in heated warehouses.
Cutting and assembly
- To cut sheets should be used special roofer’s cutter. After assembly all filing and turnigs should be removed form surface of roof. In case of any damages, it should be repaired immidiately with proper touch up paint.
- In case of using grinding machine, any complaints wont be accepted.
- Other information can be found in assembly instruction to specific product.
- To cut sheets should be used special roofer’s cutter. After assembly all filing and turnigs should be removed form surface of roof. In case of any damages, it should be repaired immidiately with proper touch up paint.
- In case of using grinding machine, any complaints wont be accepted.
- Other information can be found in assembly instruction to specific product.
Maintenance and cleaning
- In order to extend durability of roofs and elevations it’s recommended to check and conservative it.
- Inspection – One time a year (it’s best in spring) there should be inspection of roof/elevation in order to early detection of possible damage.
- Cleaning of steel sheet – Roof and elevation made of steel sheets require cleaning at least once a year. Stratifying dirt on steel sheet may cause uneven discoloration of lacquer (because of uneven impact of UV beams), and lower protection to corrosion(dust traps humidity on steel sheets which causes damage). Dirty and stained spots can be cleaned by soft brush and water (temp. max. 60c). If it is necessary it is permitted to use some light detergent (ph 6/7, max 10% solution). There also can be used pressed water(max. 100bar) to cleaning, however the beam of water cannot be applicated too near of surface of sheets(min. 30 cm), also it shouldn’t be perpendicularly to surface. Near the connections water beam should be directed to bottom, to avoid water of entering cracks near connections. With old surfaces of steel sheets we should deal with high cautiously. Cleaning should be conducted from top to bottom, and cleaned spots should be rinsed out immediately.
- It is not permitted to use scouring powders, nitro solvent, chlorine liquor, aromatised substances, substances with Amon chloride or sodium.
- Damages – Possible damages during guarantee should be consulted with Contractor of roof/elevation and can be repaired only with his written permission.Repair of damages on small surfaces is done with quick-drying varnish. However painting big surfaces should be done with special industrial paints to renovating coverings. Painting should be limited only to special damaged spots (scratches to steel, centres of corrosion etc.)Preparation of surface to painting should be done with generally accepted rules. It is necessary to precisely remove all signs of corrosion – best with special brush or close-grained sandpaper. Then that surface should be undusted, degreased and cleaned. To degrease extraction naptha or water with addition of surfactant(best with 1-2%solution of ammoniac) can be used. Repaired spots may be different in colour compared to original steel sheets because of natural impact of atmospheric phenomenon (ageing of varnish due to impact of UV radiation)
- ATTENTION!– During inspecting, cleaning, conservation and repair all work safety regulations should be obeyed.Pruszyński Sp. z o.o. is not in charge of possible accidents during carrying out all following actions.
- In order to extend durability of roofs and elevations it’s recommended to check and conservative it.
- Inspection – One time a year (it’s best in spring) there should be inspection of roof/elevation in order to early detection of possible damage.
- Cleaning of steel sheet – Roof and elevation made of steel sheets require cleaning at least once a year. Stratifying dirt on steel sheet may cause uneven discoloration of lacquer (because of uneven impact of UV beams), and lower protection to corrosion(dust traps humidity on steel sheets which causes damage). Dirty and stained spots can be cleaned by soft brush and water (temp. max. 60c). If it is necessary it is permitted to use some light detergent (ph 6/7, max 10% solution). There also can be used pressed water(max. 100bar) to cleaning, however the beam of water cannot be applicated too near of surface of sheets(min. 30 cm), also it shouldn’t be perpendicularly to surface. Near the connections water beam should be directed to bottom, to avoid water of entering cracks near connections. With old surfaces of steel sheets we should deal with high cautiously. Cleaning should be conducted from top to bottom, and cleaned spots should be rinsed out immediately.
- It is not permitted to use scouring powders, nitro solvent, chlorine liquor, aromatised substances, substances with Amon chloride or sodium.
- Damages – Possible damages during guarantee should be consulted with Contractor of roof/elevation and can be repaired only with his written permission.Repair of damages on small surfaces is done with quick-drying varnish. However painting big surfaces should be done with special industrial paints to renovating coverings. Painting should be limited only to special damaged spots (scratches to steel, centres of corrosion etc.)Preparation of surface to painting should be done with generally accepted rules. It is necessary to precisely remove all signs of corrosion – best with special brush or close-grained sandpaper. Then that surface should be undusted, degreased and cleaned. To degrease extraction naptha or water with addition of surfactant(best with 1-2%solution of ammoniac) can be used. Repaired spots may be different in colour compared to original steel sheets because of natural impact of atmospheric phenomenon (ageing of varnish due to impact of UV radiation)
- ATTENTION!– During inspecting, cleaning, conservation and repair all work safety regulations should be obeyed.Pruszyński Sp. z o.o. is not in charge of possible accidents during carrying out all following actions.
Technical specification of the coating
Available colours
Technical specification of the coating
Available colours
SILVER
SILVER METALLIC
SILVER
SILVER METALLIC
SILVER
SILVER METALLIC
Product description
Facade wall panels PS from Pruszyński is the highest quality modern solution of lightweight buildings made of sheet metal. With their appearance and function they resemble popular sidings, which are usually made of artificial materials (PVC) or wood.
The use instead of a quality galvanized sheet, which is additionally covered with a unique protective coating, is a much more favorable solution. Wall panels are characterized by higher mechanical parameters as well as much higher durability and resistance to UV rays (protective coatings).
The PS panel is a modern and aesthetic solution for covering the outer facade. Thanks to their shape, they create almost any patterns on the wall based on geometric shapes. In addition, a wide range of protective coatings color creates very interesting possibilities of combining shape with color to achieve a unique and unusual end result. In addition, the panels combine very well with various materials such as glass, concrete or other metals (aluminum).
This type of facade is most often found in commercial buildings – at sports facilities, office facilities, storage halls, while projects addressed to an individual client are increasingly appearing also using this solution – e.g. in single -family houses or housing estates.
Tags
See our offer of accessories
TORX self-drilling screws (staples)
Pruszyński Sp. z o.o
Sokołów, 05-806 Komorów
ul. Sokołowska 32b
Tel. (48-22) 738 60 00
Fax (48-22) 738 61 01
Infolinia: 880 222 444